Buy Chendi YT01-05-29-494.335-25 Lift Chair Actuator Motor

Chendi YT01-05-29-494.335-25 lift chair actuator motor

A Chendi linear actuator for a matching lift-chair mechanism. Its photographed label identifies the exact model as YT01-05-29-494.335-25. Compare the label, mounting ends and full cable arrangement with the original rather than choosing by appearance alone.

Label specifications

• Model: YT01-05-29-494.335-25
• Rated voltage: DC 29V
• Rated input: 55W
• Maximum load: 1500N
• Duty cycle: maximum 10%, maximum 2 minutes on followed by 18 minutes off

The existing listing describes a round five-pin connection and separate two-pin O/I cable. The connector close-up appears shared with another product, so compare your original connectors rather than relying on that photo for exact wiring. Speed, stroke, closed and extended dimensions and an IP rating are not established from this label.

Compatibility checks

Check the exact model, mounting ends, original installation length, required travel and each control-box connection. A matching force rating or similar-looking plug alone does not establish fit. Send CouchGuard clear photos of the old label, both ends and plugs if unsure.

How to replace a lift-chair actuator

1. Disconnect power. Unplug the chair from the wall and disconnect any battery backup. Do not work on the actuator while the chair is powered.
2. Support the moving sections. Keep the backrest and footrest securely supported so they cannot drop or shift when the actuator is detached. Keep fingers clear of pinch points; use a qualified chair technician if safe support is uncertain.
3. Record the original setup. Photograph the model label, both mounting ends, pin or retaining-clip positions, cable routing and each connector before disconnecting anything. Compare the replacement's installation length, travel, ends and plugs with the original.
4. Remove and refit. With the chair supported and power off, disconnect the old plugs and release its mounting retainers. Fit the replacement in the same orientation using the correct existing hardware and secure both ends. Do not force misaligned holes, alter wiring or substitute an unmatched connector.
5. Route and reconnect. Keep cables clear of the moving mechanism and pinch points, then reconnect only to matching original control-box connections.
6. Test carefully. Restore power only after tools and hands are clear. Briefly test the chair's movement and stop immediately if it binds, moves unexpectedly or a cable catches. Respect the label's maximum 2-minute-on/18-minute-off duty cycle.

This is general replacement guidance, not a model-specific wiring diagram. If the mechanism, mounting or connector does not match, stop and consult a qualified repairer rather than modifying the part.

Frequently asked questions

What does the label say about voltage and input? DC 29V rated voltage and 55W rated input.

What is the maximum load? The label states 1500N maximum load. Match the complete actuator configuration too.

What duty cycle is marked? Maximum 10%, maximum 2 minutes on and 18 minutes off.

Can it replace another YT01 actuator with the same plug? Not without checking the exact model, mounting dimensions, travel and wiring.

Recliner Replacement Parts Manual - FAQ’s 

Do you stock Pegar recline parts?

No unfortunately. Pegar handles have been obsolete for many years and we don’t stock any cables suitable.

How do you measure a recliner spring?

Recliner springs are measured by the overall length. You’ll find a break down of each recliner spring on each of the products pages. Simply click or tap on the “Measuring” tab.

Can I get a different shade brown?

No. There is only 1 colour brown available worldwide. There is no choice what shade of brown it is sorry.

My recliner handle measures 113mm x 70mm. Will your handles still fit?

Yes. There can be a couple mm tolerances in the measurements given.

My recliner handle measures 11cm x 7cm. Will your handles still fit?

Yes. Converted to millimetres is 110mm x 70mm.

How do you measure a recliner cable? You need to remove the trigger and cable from the recliner, disconnect the cable from the handle and use the Cable Cheat Sheet that is on the website.

How do I measure a recliner cable?

Click or Tap on the “Measuring” tab on the products page and follow the Cable Cheat Sheet to measure your cable correctly. Make sure you disconnect your cable from the handle before measuring. If you cable has broken the barrel off of the end, simply add that measurement, 3.5 or 6mm to the overall length measurement.

Can I pick up from your Coolum Beach Warehouse?

Yes you may click and collect. Best you email prior to make sure someone is in. Cash Only or order online and select “Pick Up From Coolum Beach” during checkout

Replacement Parts

CouchGuard supplies replacement parts for recliners, lift chairs and lounges, including electrical and mechanical components. Use the guidance below to help identify the correct part before ordering.

Price Match Guarantee

Found the same replacement part for a lower price from another Australian supplier? CouchGuard’s Price Match Guarantee applies to all part brands and types.

We compare the complete delivered price, not just the advertised part price. This means we compare the competitor’s part price plus delivery with CouchGuard’s part price plus delivery.

What qualifies?

• The competitor’s item must be the identical replacement part.
• The part must be currently in stock and available to purchase.
• The competitor must be an Australian supplier.
• The comparison must use the complete delivered price, including delivery charges.

How to request a price match

Have a link to the competitor’s product page ready so we can verify the part, availability, price and delivery charge. Call us on 1300 268 244, or contact us by email.

Before You Buy a Replacement Part

Replacement parts can look similar while having different model numbers, dimensions, connectors or mounting points. Before ordering:

• Check the original part for a manufacturer label, model number or part number.
• Compare the connector type, dimensions and mounting points with the product listing.
• Check the product description and compatibility guidance carefully.
• Contact CouchGuard with clear photos if you are unsure which part you need.

Additional Checks for Electrical Parts

• Check that the green light on the power supply is on.
• Check the leads and connections for visible damage.
• Check whether the switch is faulty.
• If possible, test the actuator in another compatible recliner.

These checks may help identify the fault, avoid replacing a working part and save you hundreds of dollars.

Selected Product Warranties

The following warranties apply to the listed products:

• 24-month warranty on all compatible actuators.
• 24-month warranty on all genuine Okin and TiMOTION actuators.
• 12-month warranty on all genuine Kaidi, eMoMo and Mulin actuators.
• 24-month manufacturer warranty on 6000mAh and 3950mAh batteries purchased on or after 11 September 2026.
• 12-month manufacturer warranty on the 2550mAh battery pack.

All actuators supplied by CouchGuard are tested by the manufacturer before leaving its facility. If a defect becomes apparent, contact us promptly with your order details so we can assess the product under the applicable warranty.

Warranty coverage is subject to our Purchase Terms and your rights under Australian Consumer Law.

Reach out to our team today by calling 1300 268 244 or emailing info@couchguard.com.au